BitulenTM SK 374(Self- Adhesive Waterproofing Membrane)

Do not allow Fleximent 201 to be contaminated by other materials. Gloves and google should be worn. Any splashes to the skin or eye should be washed off with clean water. Store in cool and dry place.

Description

BitulenTM SK 374 is a 1.5mm thick preformed waterproofing membrane for use both above and below grade with concrete , brickwork and blockwork constructions to protect buildings against water.

BitulenTMSK 374 comprises a special cross - laminated polyethylene film coated with modified bitumen. The underside is protected by a silicone coated release paper.

BitulenTM SK 374 has a 65mm wide selvedge protected by silicon coated release paper ,which permits achieving a homogenous joint at the overlaps of adjacent layers of membrane.

BitulenTM SK 374 meets the requirements of Singapore Standard SS 374:94 for preformed sheet membranes.

BitulenTM SK 37 provides an effective waterproofing membrane for foundations, tunnels, floors and flat roofs. Being cold-applied, it I s ideal for installation in restricted spaces.

INSTALLATION

All surfaces should be dry,smooth ,free from voids, dust or loose materials and sharp protrusions . Concrete should be cured before application of waterproofing membrane. Where the substrade is not smooth, it should be rendered or flush point to give a smooth surface.

Surfaces must be primed with an approved high penetration aliphatic primerandallowedto dry tack-free before installing BitulenTM SK 374

All inside and outside corners should be covered by first applying a 300mm wide strip of BitulenTM SK374 before the installing of the full width membrane.

After removing the release paper, BitulenTM SK 374 is then pressure bonded to the substrate. Apply pressure from the center to prevent air being trapped. All laps must be at least 65mm wide.

For floors, the installation of BitulenTM SK 374 should be continued up the wall to connect with the damp-proof course in the walls.A fillet should be placed at junction and covered with a reinforcing strip prior to installing membrane.

Aswith all waterproofing membranes, BitulenTM SK 374 should be protect by a screed or other protective layer immediately after installation. When hydrostatic pressure is present an external specification should be used.

PROPERTIES

  Test Method   Typical Value
Thickness(mm)   -   1.5
Tensile strength (N/mm2)   SS 374   >4.2 (long.)
>4.8 (trans.)
Elongation (%)   SS 374   >300(long.)
>220(trans.)
Tensile shear at joints (N)   SS 374   357
Resistance to leakage at joints   SS 374   Passed
Hydrostatic test   SS 374   Passed
Water Vapour transmission (g/m2/ hr)   SS 374   0.035
Water absorption(%)   SS 374   0.153
Dimension stability(%)   SS 374   +0.05(long.)
+0.04(trans.)
Softening point ?C   DIN 52001   98
Service temperature   -20?C to 80?C  

Bitulen-SK 374

  • Bitulen-SK 374 Bitulen-SK 374 သည္ အထူး 1.5 mm ရိွေသာေရလံုကတၱရာအလိပ္ ျဖစ္သည္။ Bitulen-SK 374 ကို ကြန္ကရစ္၏ အေပၚ (သို႔) ေအာက္ ႏွစ္ဘက္စလံုးတြင္ အသံုးျပဳႏိုင္သည္။
  • ကြန္ကရစ္ သာမကအုတ္စီထားေသာ အုပ္တံုးမ်ား (Block Work) တို႔တြင္ပါ ေရလံုအလႊာအျဖစ္ အသံုးျပဳႏိုင္ပါသည္။
  • Bitulen-SK 374 အဆင့္ျမင့္ ကတၱရာအလႊာကို Polythene အလႊာျဖင့္ ဖံုးအုပ္ထားပါသည္။ ေအာက္ဘက္ကို Silicon ဖံုးအုပ္ထားေသာ (ဆြဲခြာ၍ရေသာ စကၠဴျဖင့္) ကပ္ထားပါသည္။
  • Bitulen-SK 374 တြင္ 65mm က်ယ္ေသာအစြန္းႏွစ္ခုထပ္ရန္ ေနရာပါရိွေသာေၾကာင့္ အစႏွစ္ခုထပ္ စပ္ေၾကာင္းအားလံုၿခံဳရိွရန္ Selvedge ပါရိွပါသည္။
  • Bitulen-SK 374 သည္ စကၤာပူနိုင္ငံ၏ လိုအပ္ခ်က္အရ စံခ်ိန္ SS 374 : 94 ျဖင့္ ထုတ္လုပ္ထားေသာကတၱရာအခ်ပ္ Sheet Membrane ျဖစ္ပါသည္။
  • Bitulen-SK 374 အေဆာက္အဦး၏ အုတ္ျမစ္ (Foundation Tunnel - ေျမေအာက္ဥမင္) ၾကမ္းခင္းႏွင့္ အမိုး၊ Flat Roof Slab တို႔ႏွင့္ အေဆာက္အဦး၏ ေရလံုရန္ လိုအပ္သည့္ သီးသန္႔အထူးေနရာမ်ားတြင္ အသံုးျပဳနိုင္ပါသည္။